A seam will be found at the junction of the tub flange and the backer board on the bathtub's back wall. This is the area where caulk will be used to seal the seam. But, there are some areas that cannot be sealed and might need to repaired. This area should be sealed and repaired by following the appropriate procedures.
The tub surround should be level at the back. Before you install the tub surround, remove the old one. You can use a pry bar or a hammer to do this. You should also wear protective gear.
You have the option to put a tub surround in concrete, wood or tile depending on what you need. There are many options for these surrounds. These surrounds are most commonly made of acrylic or plastic panels. Each type comes with its own set of instructions. Some kits only include a back panel, while others include both. You can save money by purchasing a single-piece surround.
After you have removed the old surround, remove the corner panels. You will then need to measure your new surround to determine its dimension. It's important to have the right adhesive to ensure it sticks well. It will be necessary to adhere adhesive to multiple areas at once. Allow enough time for the adhesive to dry.
When you're ready to start applying the adhesive, mark the left and right sides of your wall and the top and bottom of the surround. This will provide you with a visual guideline for where to apply adhesive. You must cut the adhesive lines correctly. To make lines visible, masking tape is an option.
Place the back of the surround against a wall, and then adjust the back to flush. The back should be flat against the drywall. If the back section isn't level, you can add additional adhesive to close the gap. After you've applied the adhesive, let it dry at least 24 hours.
Now you can start putting in the tub surround's back wall. This is the most straightforward part. It's best to have someone hold it to ensure that it doesn't move. Another option is to place a level across your surface and guide the installation.
Afterwards, you'll want to attach the flanges to the studs. You should drive fasteners through predrilled holes that are slightly larger than the actual size. For added support, add a few 2x4 nailers. They should be attached directly to wall framing, but not to the drywall.
Before you start tiling you'll need to put on the appropriate vapor barrier. A vapor barrier consists of thick plastic sheets that protect the wall from moisture. You will also need primer and paint. Several different types of glue are available, so be sure to check the manufacturer's directions for more information.
FAQ
Do I need an architect/builder?
If you are planning to renovate your own home, it may be easier to just hire someone else to do the work for you. An architect or builder is a good option if you plan to buy a new house.
How much does it cost to renovate a house?
Renovations typically cost anywhere from $5,000 to $50,000. Renovations can cost homeowners anywhere from $10,000 to $20,000
How can you remodel a house without spending any money?
Here are some tips to help you renovate your home without spending too much money.
-
Plan your budget
-
Find out the materials you require
-
Decide where you want to put them
-
Make a list with the items you need to purchase
-
Find out how much money your have
-
Plan your renovation project
-
Get to work on your plans
-
Online research is a good idea.
-
Ask family and friends for their help
-
Be creative!
Is it better to finish floors or walls first?
The best way of starting any project is to determine what you want. It is important that you think about how and who you want to use the space. This will help to decide whether flooring or wall coverings is best for you.
If you have decided that you want to create an open plan kitchen/living area then you may choose to install flooring first. Wall coverings are an option if you prefer to keep this space private.
Can I remodel my whole house by myself?
Why pay someone to do it for you when you can do it yourself?
It doesn't really matter how much you love DIY. There will always be times when you just can't do it. There may be too many variables involved for you to control.
For example, if you live in an old home, you might find that the wiring is outdated and you would need to hire a qualified electrician to make sure that your electrical system is safe and reliable.
It is possible that your renovations might cause structural damage.
It is possible that you don't have the right tools or the knowledge to do the job correctly. For example, if your goal is to install a new sink in your kitchen, you will need to purchase a plumber’s snake, which is designed to clear blocked pipes.
You must also follow plumbing codes to ensure that a licensed plumber is working on your project.
It is important to understand your capabilities before embarking on such a large task.
Ask for assistance from family and friends who have completed similar tasks before if you are uncertain.
They can offer advice about what to do and where to go for more information.
Statistics
- According to the National Association of the Remodeling Industry's 2019 remodeling impact report , realtors estimate that homeowners can recover 59% of the cost of a complete kitchen renovation if they sell their home. (bhg.com)
- The average fixed rate for a home-equity loan was recently 5.27%, and the average variable rate for a HELOC was 5.49%, according to Bankrate.com. (kiplinger.com)
- A final payment of, say, 5% to 10% will be due when the space is livable and usable (your contract probably will say "substantial completion"). (kiplinger.com)
- Most lenders will lend you up to 75% or 80% of the appraised value of your home, but some will go higher. (kiplinger.com)
- Rather, allot 10% to 15% for a contingency fund to pay for unexpected construction issues. (kiplinger.com)
External Links
How To
Do you prefer renovating exterior or interior?
Which one should you do first?
There are many factors you need to consider when choosing which project you want to work on. The most common factor is whether the building is old or new. The condition of the roof, windows and doors, flooring, wiring, and other aspects are all important. The location, style, number of rooms and size of a new building are all important aspects.
If the building is old, the first thing to look at is the roof. You might consider starting the renovation immediately if the roof appears to be in danger. If the roof is fine, then you can move onto the next step. Next, look at the windows. If the windows are dirty or broken, you may need them to be replaced. Next, clean the doors and ensure that they are free of debris. Next, check that everything seems to be in order before you begin work on the floors. You should ensure that the flooring does not crack or become unstable no matter how many times you walk on them. Now you can start to add the walls. You can now examine the walls to check for cracks or damage. If the wall appears to be in good shape, you can continue to the next steps. You can now inspect the ceiling. The ceiling should be inspected to make sure it can support any weight that you might place on it. If all is well, then you are ready to move on to the next phase of your renovation.
You would want to begin with the exterior if the building was recently built. Start by looking at the outside. Is it in good condition? Is it free from cracks? Does it look good overall? If the exterior doesn't look great, then you should definitely fix it. You don't want to let your home look bad. Next, inspect the foundation. You should repair any foundation that appears weak. Also, inspect your driveway. You want it to be smooth and flat. If it isn't, then you should probably fix it. You should also inspect the sidewalk while you're checking your driveway. If it's not level, you might need to replace it.
After you have checked these areas, you can move on to the interior of your house. Begin by inspecting the kitchen. Is it clean and well kept? If it is unorganized, it should be cleaned. Next, make sure to inspect the appliances. They should be in good shape and working properly. If they're not, you can either replace them or repair them. The cabinets should be inspected after that. Paint them if they're stained or scratched. You can then move on to the bathroom if they are in good condition. The toilet should be inspected here. If the toilet is leaking, you will need to replace it. If it's just dirty, then you should probably wash it. Next, take a look at all of the fixtures. You should make sure they are clean. You should clean them if they are stained. Finally, make sure to inspect the countertops. You should repaint countertops that are cracked or chipped. Use a sealant if they're shiny and smooth.
The last step is to check the furniture. Check that nothing is damaged or missing. If something is missing or damaged, then you should likely find it. If it is damaged, you should probably fix it. After everything has been checked, you can go outside to finish the job.