A popular way to give a room character and beauty is to install tongue and groove panels over drywall. You have many options for how to install this type paneling. However, all of them require accurate measuring and cutting. The most common technique is to nail panels directly to furring strips that run vertically across the wall. You can also install diagonally by using a 45-degree angle at each end of each panel to create the long groove side.
Installation Steps
You will need to take out all electrical outlets, hooks, and nails from the wall before you can hang wood planks on drywall. Also, you'll need to sand any protrusions from the walls. You can use either a power sander to do this or large sandpaper pieces and an extension basis.
Determine whether your tongue and groove paneling is nailed to drywall or studs
Placing a prybar at the corner of two walls is a good way to verify that the tongue and groove wall panels have been nailed to the drywall. With your hammer, gently tap the pry bar into the seam where the two walls meet. You will need to remove the panel from the wall if it isn't nailed to the drywall using a prybar and pliers.
You should determine whether your tongue & groove wall panels were nailed, glued or both
Once you are certain your paneling and drywall are nailed, start removing trim. You should be able reuse the trim.
If you cannot reuse the trim, you will need to purchase new wood panels. To determine the number of sheets 4'x8' you will need, measure the wall you are covering. If you have walls greater than 8 feet tall, subtract one panel for each door and one panel for each window.
Marking a Straight Edge on Drywall
You can ensure that the wood paneling is properly installed across the drywall surface by running a straight line from one end to the other. Be aware of any areas where the wall is higher than or lower than the wood paneling. If the drywall bulges it will cause your paneling not to lay flat or stick out too much.
Dust Mask for Drywall Sanding
You should sand any areas where the drywall is protruding when installing tongue and groove panels over drywall. This will make it easier and more even to install your paneling.
Finishing with Wood Potty
After you've sanded off the drywall, apply wood glue to the walls. The paneling can also be stained with a wood stain for a more natural look. However, this requires more labor than applying paint.
Drywall Attachment Paneling
You will need a nail set that has rounded heads to attach wood paneling and drywall. These fasteners are easily found at hardware stores and typically cost $4 for 16-penny common nails. They can be used on any type of wood such as plywood or drywall. However, they are not recommended for use with thicker boards.
FAQ
How do I start a renovation of a house?
Cleaning out clutter inside and out is the first step to fixing up a house. Next, you will need to eliminate mold, repair or replace any damaged walls, repaint your entire interior, and fix any leaky pipes. You will need to clean up the exterior and paint.
Is it better to remodel an older house than build a brand new one?
There are two options available to you if you're considering building a home. One option is to buy a pre-built home. This type home is already constructed and ready for you to move in. A custom-built home is another option. You will need to hire a professional builder to help design and construct your dream home.
How much time and effort you put into designing and planning your new home will determine the cost. Because you will likely be doing most of the work yourself, a custom home can require more effort. But you can choose the materials you want and where you want them to be placed. It might be easier to find a contractor that specializes in custom-built homes.
A new house is generally more expensive than a home that has been renovated. You'll have to pay more for land and any improvements. Plus, you'll need to pay for permits and inspections. The average price difference between a new home and one that has been renovated is between $10,000 and $20,000.
What can I do to save money on my home's renovation?
By doing all the work yourself, you can save money. One way to save money is to try and reduce the number people who are involved in the remodeling process. Another option is to try to lower the cost of the materials you use in your renovations.
Is it better to finish floors or walls first?
It is the best way to begin any project. It is crucial to plan how you'll use the space, what people will use it for, and why. This will help to decide whether flooring or wall coverings is best for you.
You may want to lay flooring before you create an open-plan kitchen/living space. You can also choose wall coverings if you want to make the room private.
Statistics
- ‘The potential added value of a loft conversion, which could create an extra bedroom and ensuite, could be as much as 20 per cent and 15 per cent for a garage conversion.' (realhomes.com)
- The average fixed rate for a home-equity loan was recently 5.27%, and the average variable rate for a HELOC was 5.49%, according to Bankrate.com. (kiplinger.com)
- According to the National Association of the Remodeling Industry's 2019 remodeling impact report , realtors estimate that homeowners can recover 59% of the cost of a complete kitchen renovation if they sell their home. (bhg.com)
- A final payment of, say, 5% to 10% will be due when the space is livable and usable (your contract probably will say "substantial completion"). (kiplinger.com)
- Design-builders may ask for a down payment of up to 25% or 33% of the job cost, says the NARI. (kiplinger.com)
External Links
How To
Are you renovating the exterior or interior first?
Which one should I first do?
There are many aspects to consider when choosing which project should be started. Most people consider whether the building is new or old. It is important to assess the condition of the roof and windows as well as the doors, flooring, and electrical system. When the building is new, there are many things to consider such as its location, size, number, style, and so forth.
The roof should be the first thing you look at if the building's age is a concern. If it looks like the roof could collapse any minute now, you may want to start on the renovation. The roof should be in good shape before you move on to the next stage. Next, examine the windows. Next, inspect the windows and make sure they are clean. After this, go through the doorways and make sure that they are clean and free from debris. If everything looks good, you can start to lay the flooring. Make sure that the flooring is solid and sturdy so that no matter how hard you walk on it, nothing breaks. Once these steps are done, then you can move on to the walls. You can now examine the walls to check for cracks or damage. If the wall appears to be in good shape, you can continue to the next steps. You can now inspect the ceiling. It is important to inspect the ceiling and ensure it is strong enough for any weight you may place on it. You can then move on with your renovation if everything looks good.
If your building was constructed recently, you might want to look at the exterior. Take a look at the outside of your house. Is the house well-maintained? Is it free from cracks? Is it in good condition? If your exterior isn't looking great, you should make some changes. It is not a good idea to make your home look unattractive. Next, make sure to check the foundation. If the foundation looks weak, then you should repair it. Also, be sure to check your driveway. It should be straight and level. It should be smooth and flat. If it isn’t, you need to fix it. Also check the sidewalk when you are checking the driveway. If it's uneven, then you should probably replace it.
After you have checked these areas, you can move on to the interior of your house. First, take a look at the kitchen. Is it clean and well kept? If it is messy, then you should probably clean it up. Next, inspect the appliances. You want them to be in good order and working correctly. If they're not, you can either replace them or repair them. Check the cabinets after this. Paint them if they're stained or scratched. If they are in great condition, then you can go to the bathroom. Check the toilet in here. You should replace it if it leaks. You can wash it if it is just dirty. Next, inspect all fixtures. Check that the fixtures are clean. If they are filthy, clean them immediately. You should also inspect the countertops. Repainting countertops is advisable if they have cracked or are chipped. Sealant should be used if the surfaces are smooth and shiny.
Final step: Check your furniture. Verify that the furniture is not damaged or missing. If it's missing or damaged, you need to find it. It is best to repair any broken items. Once you have checked everything, you can return outside to complete the job.